As propriedades de recuperação de forma da liga à base de Fe-Mn-Si-Cr-Ni-Co foram estudadas usando ensaio de compressão. Foram analisadas medidas de recuperação elástica (Re), recuperação de forma (Rf) e recuperação de forma total (R T = Re + Rf) em função do número de ciclos de treinamento. Os resultados indicaram que 3,3 foi a melhor razão entre altura (h o = 20 mm) e diâmetro (φo = 6 mm) para se conseguirem uma deformação homogênea e curvas de carregamento bem definidas. A maior contribuição para a R T foi atribuída à recuperação de forma. No último ciclo de treinamento, foi obtida uma R T = 90%, sendo 25% atribuída a Re.

The shape recovery properties of an Fe-Mn-Si-Cr-Ni-Co based alloy were studied using compression tests. Analyzed were the elastic recovery (Er), shape recovery (Sr) and total shape recovery (T SR = Er + Sr) measurements as a function of training cycles. The results indicated that 3.3 was the best ratio between height (h o = 20 mm) and diameter (φo = 6 mm) to obtain a homogeneous deformation and defined loading curves. A major contribution of T SR was attributed to shape recovery. In the last training cycle, a T SR = 90 % was obtained, where 25% was attributed to Er.

RESUMO Esse trabalho apresenta um estudo da dureza e do mee austenita-γ da liga inoxidável à base de ferro com efeito de memória de forma. Utilizando indentação instrumentada, foi possível determinar a dureza e o módulo de elasticidade das fases austenita-γ e martensita-ε separadamente. A fase martensítica apresentou uma dureza de 7,0 GPa, enquanto que a dureza da fase austenítica foi de 3,0 GPa. Os valores de módulo de elasticidade foram 202 e 137 GPa, para as fases martensita e austenita, respectivamente.

ABSTRACT This work presents a hardness study and elastic modulus for the ε-martensite and γ-austenite phases of an iron based shape memory alloy. Using instrumented indentation, it was possible to determine the hardness and elasticity modulus of these phases separately. The martensitic phase presented a hardness of 7.0 GPa and the austenitic phase presented a hardness of 3.0 GPa. The elastic modulus values were 202 and 137 GPa for the martensitic and austenitic phases, respectively.

Nesse trabalho, apresentamos a caracterização estrutural de regiões soldadas em aço austenítico AISI-304, que foram submetidas a processo de nitretação a plasma (20%N2 + 80%H2). Posteriormente as amostras foram hidrogenadas catodicamente. As temperaturas de nitretação foram de 400, 500 e 550°C. As regiões da solda e fora da solda hidrogenadas após a nitretação foram comparadas por DRX, microscopia ótica e microscopia eletrônica de varredura (MEV). As fases austenita-γ, martensita-α', martensita-ε, ferrita-α e os nitretos CrN, γ'-Fe4N e e-Fe2+xN foram identificados. As microestruturas de ambas as regiões e da zona termicamente ativada (ZTA) foram similares. Para 400°C, a estequiometria das fases formadas foi diferente das observadas em 500°C e 550°C. Os efeitos provocados pela hidrogenação foram mais acentuados em 550°C, com o arrancamento da camada nitretada.

Structural characterization of weld and outside weld regions of AISI-304 nitrided (20%N + 80%H) and cathodically hydrogenated is presented. Nitriding temperatures were 400, 500 e 550°C. The weld and outside weld regions were compared by XRD, optical microscopy and SEM. The phases γ-austenite, α'-martensite, ε-martensita and α-ferrite and the nitrides: CrN, γ'-Fe4N e e-Fe2+xN were identified. Microstructures of both regions and the thermal active zone were similar. For 400°C the stoichiometry of the formed phases was different from that formed at 500°C and 550°C. Hydrogen effects were more intense for 550°C, due to chipping occurrence.

Mechanical and tribological properties os AISI 304 and AISI 316 stainless steels submited to glow discharge ion nitriding are reported.The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ´-Fe4N and - Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.

The aim of this work was to study the effect of austenitic grain size (GS) reduction on the structural parameters of the epsilonhcp - martensite in stainless shape memory alloy (SMA). Rietveld refinement data showed an expansion in c-axis and a reduction in a and b-axis with thermo-mechanical cycles for all samples analyzed. Samples with 75 < GS (µm) < 129 were analyzed. It was also observed an increase of the unit cell volume in this phase with GS reduction. The smallest grain size sample (GS = 75 µm) presented a c/a ratio of 1.649, and approximately 90% of total shape memory recovery.

The temperature induced phase transition in MnAs is analyzed in this work using X ray Rietveld refinement. The results show the presence of the hexagonal phase (P6(3)/mmc) at room temperature and the first-order structural-magnetic transition to the orthorhombic phase (Pnma) around 318 K was followed in detail. The MnAs magnetic characterization allowed to obtain the transition temperature and a maximum value of 47 J/(kg.K) for the measured magnetocaloric effect for a magnetic field variation of 5 T.